- Tipo
- Applicazione
- Numero di attacchi
- Metodo di installazione
- Caratteristiche
- Numero di solenoidi
- Tipo singolo
- Tipo singolo
- A commutazione
- Stato allo spegnimento
- Tensione
- Tipo di attacco tubo
- Filettatura tubazione nominale
- Tipo di azionamento
- Valore CV
- 0.008
- Con tenuta
- Pressione nominale(MPa)
- Specifiche bobina
- Ingresso elettrico conduttore
- Manuale
- Spia / circuito di protezione
- Tipo
- CAD
- 2D
- 3D
- Giorni di spedizione est.
- Tutti
- Entro 4 giorni lavorativi
V100, Elettrovalvola a 3 vie - Standard (V114T-5MNZ-M5)
Informazioni sul prodotto
3-Port Solenoid Valve, Direct Operated, Rubber Seal, V100 Series Specifications
3-Port Solenoid Valve, Direct Operated, Rubber Seal, V100 Series external appearance
V114 (A) and V124 (A) JIS symbols
| Fluid | Air |
|---|---|
| Ambient Temperature and Operating Fluid Temperature °C | -10 to +50 (no freezing) |
| *1Response Time (for DC) ms | ON: 5 or less, OFF: 4 or less |
| Maximum Operating Frequency Hz | 20 |
| Manual Operation | Non-locking push type, locking type screwdriver operated type (slotted) |
| Lubrication | Not required |
| Mounting Position | Free |
| *2: Impact Resistance / Vibration Resistance: m/s2 | 150/30 |
| Enclosure | Dust-proof |
*1: Based on JIS B 8419:2010 dynamic performance test. (Standard type: coil temperature of 20°C, at rated voltage, with no surge voltage suppressor)
*2: Impact resistance: No malfunctions after testing using an impact tester under the following conditions: in the axial direction and at a right angle to the armature in both energized and non-energized states (once for each condition state). (Initial value)
Vibration resistance: No malfunctions occurred in a 1-sweep test between 45 and 2,000 Hz. The test was performed in both energized and non-energized states and in the axial direction and at a right angle to the armature. (Initial value)
Solenoid Specifications
| Series | V114/V124 | V114A/V124A | ||
|---|---|---|---|---|
| Electrical Entry | Grommet (G) / (H), L-shaped plug connector (L), M-shaped plug connector (M) | |||
| Coil rated voltage (V) | DC | 24, 12, 6, 5, 3 | ||
| AC 50/60 Hz | 100, 110, 200, 220 | - | ||
| Allowable Voltage Fluctuation | -10 to +10%* | |||
| Power Consumption W | DC | Standard: 0.35 (with light: 0.4), with energy-saving circuit: 0.1 *[startup: 0.4, holding: 0.1] | 1 W (with light: 1.1) | |
| Apparent Power VA | AC | 100 V | 0.78 (with light: 0.81) | - |
| 110 V [115 V] | 0.86 (with light: 0.89) [0.94 (with light: 0.97)] | - | ||
| 200 V | 1.18 (with light: 1.22) | - | ||
| 220 V [230 V] | 1.30 (with light: 1.34) [1.42 (with light: 1.46)] | - | ||
| Surge Voltage Suppressor | See the SMC catalog. | |||
| Indicator Light | LED | |||
- The 110‑V AC and 115‑V AC types are interchangeable. The 220‑V AC and 230‑V AC types are also interchangeable.
- For 115 V AC and 230 V AC, the allowable voltage fluctuation is -15 to +5% of the rated voltage.
- As the S, Z, and T types (with power saving circuit) have voltage drop due to the internal circuits, the allowable voltage fluctuation should be within the range given below.
S, Z type 24 V DC: -7% to +10%
12 V DC: -4% to +10%, T type 24 V DC: -8% to +10%
12 V DC: -6% to +10% - *If the valve is continuously energized for long periods, use an energy-saving type or DC specification.
*Refer to the SMC catalog for details.
Model
| Valve Model Numbers | Switching Method | Type | Operating Pressure Range *4 (MPa) | When Using in Vacuum (MPa) *4 | Piping connection port diameter | Weight (g) *2 | |||
|---|---|---|---|---|---|---|---|---|---|
| Port 1 | 3-Port | Port 1, Port 3 | 2 port | Grommet Type | L Type, M Type | ||||
| V114 | N.C. | Standard | 0 to 0.7 | -100 kPa to 0.6 | -100 kPa to 0 | M5 ×; 0.8 | M5 ×; 0.8 | V1□4: 13 (27) V1□4A: 16 (30) | Plug connector V1□4: 12 (26) V1□4A: 16 (29) |
| V114A | N.C. | High flow rate | 0 to 0.7 | -100 kPa to 0.6 | -100 kPa to 0 | M5 ×; 0.8 | M5 ×; 0.8 | ||
| V124*1 | N.C. | Standard | 0 to 0.7 | -100 kPa to 0 | -100 kPa to 0.6 | M5 ×; 0.8 | M5 ×; 0.8 | ||
| V124A*1 | N.C. | High flow rate | 0 to 0.7 | -100 kPa to 0 | -100 kPa to 0.6 | M5 ×; 0.8 | M5 ×; 0.8 | ||
| Valve Model Numbers | Flow Rate Characteristics | |||||
|---|---|---|---|---|---|---|
| 1 → 2 [3 → 2 *3] | 2 → 3 [2 → 1 *3] | |||||
| C [dm3/(s·bar)] | b | Cv | C [dm3/(s·bar)] | b | Cv | |
| V114 | 0.037 | 0.11 | 0.008 | 0.054 | 0.35 | 0.015 |
| V114A | 0.076 | 0.07 | 0.016 | 0.099 | 0.23 | 0.024 |
| V124*1 | 0.054 | 0.35 | 0.015 | 0.037 | 0.11 | 0.008 |
| V124A*1 | 0.099 | 0.23 | 0.024 | 0.076 | 0.07 | 0.016 |
*1: For V124 and V124A, apply pressure from port 3 and exhaust from port 1.
*2: Values in ( ) are with the subplate.
*3: For 10-V124 (A).
*4: When the difference between the primary and secondary sides is extremely small (guideline is 0.001 MPa or less), the quality of the air and lubricant oil in the solenoid valve (condensate mixture, etc.) may prevent air from being output or may cause the flow rate to dramatically decrease.
Structure Drawing
Structure Drawing
Component Parts
| Number | Part name | Material |
|---|---|---|
| 1 | Body | Resin |
| 2 | Cover | SUS |
| 3 | Push Rod | Resin |
| 4 | Armature Assembly | SUS, resin |
| 5 | Poppet | FKM |
| 6 | Return Spring | SUS |
| 7 | Poppet Spring | SUS |
| 8 | Coil Assembly | - |
| 9 | Manual | Resin |
Replacement Parts
| Number | Part name | Part number | Material | Note |
|---|---|---|---|---|
| 10 | Gasket Assembly | V100-31-1A | FKM, steel | Gasket, 2 screws |
| 11 | Sub-plate | V100-74-1 | Zinc diecast | - |
Outline dimensional drawing
Base Mounting Type (with Sub-Plate)
(Unit: mm)
Grommet (G), (H): V114/124 (A)-□G / H□□-M5 drawing
*Values in [ ] are for AC.
Values in < > are for the large flow capacity type (A).
(Unit: mm)
L-shaped plug connector (L): V114/124 )(A)-□L□□-M5 drawing
Other dimensions are the same as the grommet type.
(Unit: mm)
M type plug connector (M): V114/124 (A)-□M□□-M5 drawing
Other dimensions are the same as the grommet type.
Ulteriori informazioni
Informazioni di base
SMC Solenoid Valve.
[Features]
· Power consumption: 0.1 W (with power saving circuit)
Attenzione
- Le immagini dei prodotti possono essere rappresentative. Fare riferimento al catalogo del produttore per i dettagli.