IDK, Tubo anticondensa (Polimero di resina fluorurata)

IDK, Tubo anticondensa (Polimero di resina fluorurata)
[Features]
· Prevents condensation in small cylinders and air grippers.
· Draws out internal water vapor.
· No power supply or additional engineering required.
· Just install the Moisture Control Tube into your existing setup and go.

(i)Nota

  • Refer to the catalog for product specifications.
  • Product images may be representative images. Refer to the catalog for details.

Codice componente

Qui sono indicati i codici componente
correlati al prodotto ricercato

Moisture Control Tube IDK Series Specifications

Straight type

IDK Series (Straight Type) external appearance

IDK Series (Straight Type) external appearance

Inner sleeve external appearance

Inner sleeve external appearance

Model IDK02 IDK04 IDK06
Fluid*1 Compressed air
Maximum operating pressure 0.7 MPa
Operating temperature 0 to 60°C (no freezing)
Operating environment*2) Indoors where there is no exposure to water, etc. (0 to 40°C, 0 to 75% RH)
Minimum bending radius*3) mm 10 20 40
Number of moisture control
tubes
2 pcs
Color Transparent [Color will turn to brown over time but the functions are not affected. ]
Applicable fittings*4) KQ2
Material Fluoropolymer

*1: Use the moisture control tube with a refrigerated air dryer and a mist separator installed in the upstream compressed air line. The condensation prevention performance may be lowered depending on the quality of the compressed air (oil, dewpoint) supplied.
*2: Use the product in an operating environment where humidity is low. The condensation prevention performance may be lowered if used under a high-humidity environment.
*3: Minimum bending radius is the value at which the moisture control tube is bent or flattened at 20°C. During actual use, be careful not to bend or flatten, etc., the tube or the inner sleeve.
*4: The inner sleeve is already mounted and cannot be removed. If the inner sleeve comes off, re-insert the sleeve before mounting the fitting.
*5: Do not cut the tube.

Drawings

Straight Type dimensional drawing

Straight Type dimensional drawing

 

(Units: mm)

 

Model Outer diameter ×; inner diameter
D
Nominal length
X
Full length
L
IDK02-100 2 ×; 1.2 100 120
IDK02-200 200 220
IDK04-100 4 ×; 2.5 100 140
IDK04-200 200 240
IDK06-100 6 ×; 4 100 140
IDK06-200 200 240

*Dimensions at 40% relative humidity. Dimensions may change if the relative humidity changes.

Coil Shape Type

IDK Series (Coil Shape Type) external appearance

IDK Series (Coil Shape Type) external appearance

Model IDK04-□-C1 IDK06-□-C1
Fluid*1 Compressed air
Maximum operating pressure 0.7 MPa
Fluid temperature 0 to 60°C (no freezing)
Operating environment*2 Indoors where product is not exposed to water, etc. (0 to 40°C, 0 to 75% RH)
Number of moisture control tubes 2 pcs
Color Transparent [Color will turn to brown over time,
but the functions are not affected. ]
Applicable fittings*3) KQ2
Material Fluoropolymer

*1: Use the moisture control tube with a refrigerated air dryer and a mist separator installed in the upstream compressed air line. The condensation prevention performance may be lowered depending on the quality of the compressed air (oil, dewpoint) supplied.
*2: Use the product in an operating environment where humidity is low. The condensation prevention performance may be lowered if used under a high-humidity environment.
*3: The inner sleeve is already mounted and cannot be removed. If the inner sleeve comes off, re-insert the sleeve before mounting the fitting.

Drawing (Per Tube)

 

(Units: mm)

 

IDK04-100-C1 dimensional drawing

IDK04-100-C1 dimensional drawing

 

(Units: mm)

 

IDK04-200-C1 dimensional drawing

IDK04-200-C1 dimensional drawing

 

(Units: mm)

 

Part B details

Part B details

 

(Units: mm)

 

IDK06-100-C1 dimensional drawing

IDK06-100-C1 dimensional drawing

 

(Units: mm)

 

IDK06-200-C1 dimensional drawing

IDK06-200-C1 dimensional drawing

  • *Due to the material, the above dimensions may vary depending on the environment (temperature and humidity), including expansion of Part A.
  • *The images are representative models. The appearance may differ from the actual product.
Codice componente
IDK02-100
IDK02-200
IDK04-100
IDK04-100-C1
IDK04-200
IDK04-200-C1
IDK06-100
IDK06-100-C1
IDK06-200
IDK06-200-C1
Codice componente
Prezzo unitario standard
Quantità minima d'ordineSconto volumi elevati
Giorni
spedizione standard
?
Tipo D.E. D
(Ø)
D.E. [Distinzione] D.I. d
(Ø)
D.I. [Distinzione] Numero di anime
(Conduttore)
Min. raggio di curvatura
(mm)
Temperatura d'esercizio
(°C)
Gamma pressione d'esercizio (durante l'uso di aria)
(MPa)
Lunghezza
(m)

34.93 €

1 26 giorni Dritto-Fino a 2-Fino a 2-10--0.1

44.01 €

1 4 giorni Dritto-Fino a 2-Fino a 2-10--0.2

49.61 €

1 4 giorni Dritto4Fino a 42.5Fino a 3-20--0.1

65.66 €

1 4 giorni Spirale4Fino a 42.5Fino a 31-0~60null~0.70.1

66.09 €

1 Stesso giorno

Stock

Dritto4Fino a 42.5Fino a 3-20--0.2

88.09 €

1 26 giorni Spirale-Fino a 4-Fino a 31-0~ 60null~0.70.2

64.29 €

1 4 giorni Dritto6Fino a 64Fino a 41400~60null~0.70.1

86.27 €

1 26 giorni Spirale-Fino a 6-Fino a 41-0~ 60null~0.70.1

89.90 €

1 4 giorni Dritto6Fino a 64Fino a 4-40--0.2

119.29 €

1 26 giorni Spirale-Fino a 6-Fino a 41-0~ 60null~0.70.2

Loading...

  1. 1

Informazioni di base

Uso servizio taglio Disponibile Materiale Fluororesina Liquido applicabile Aria
Ambiente d'esercizio Standard Colore Rosso intenso

Supporto tecnico