Tubazione in fluoropolimero morbido serie TD/TID (TID01-8)
Dettagli del prodotto:
Codice articolo del costruttore: TID01-8
Marca: SMC
Prezzo: 35.58 €
Tempi di consegna: 4 giorni
Dati Tecnici:
D.E. D: 3.18 Ø
D.E. [Distinzione]: Fino a 4
D.I. d: - Ø
D.I. [Distinzione]: Fino a 3
Min. raggio di curvatura: 15 mm
(i)Nota
- I valori massimi di pressione operativa elencati sono pari a 20°C o meno. Consulta il catalogo per i dettagli.
- Le ultime cifre dei codici prodotto indicano la lunghezza dei tubi.
Codice componente
Qui sono indicati i codici componente
correlati al prodotto ricercato
TID01-8
- Dati prodotto
- Dati CAD non disponibili
Specifications of Soft Fluoropolymer Tubing TD Series
| Size | Metric Size | |||||
|---|---|---|---|---|---|---|
| Nominal | TD0425 | TD0604 | TD0806 | TD1075 | TD1209 | |
| Outer diameter (mm) | 4 | 6 | 8 | 10 | 12 | |
| Inner diameter (mm) | 2.5 | 4 | 6 | 7.5 | 9 | |
| Roll | 10 m | ● | ● | ● | ● | ● |
| 20 m | ● | ● | ● | ● | ● | |
| Color | Translucent (material color) | |||||
| Applicable Fluids | See the catalog for applicable fluids. | |||||
| FluidNote 1) | Air, waterNote 1), inert gas | |||||
| Applicable fittingsNote 1) | Insert fittings KF Series Stainless steel 316 insert fittings KFG2 Series Miniature fittings M, MS Series (Hose-nipple type) Fluoropolymer fittings LQ Series | |||||
| Maximum operating pressure (MPa) | 20°C | 1.6 | 1.4 | 0.9 | 0.9 | 0.9 |
| 100°C | 0.9 | 0.7 | 0.5 | 0.5 | 0.5 | |
| 200°C | 0.45 | 0.35 | 0.25 | 0.25 | 0.25 | |
| 260°C | 0.23 | 0.2 | 0.15 | 0.15 | 0.15 | |
| Minimum bending radius mmNote 3) | Recommended radius | 15 | 25 | 45 | 55 | 75 |
| Tube close bend radius | 8 | 16 | 31 | 35 | 41 | |
| Maximum operating temperature (fixed usage) | 260°C | |||||
| Material | Modified PTFE (Polytetrafluoroethylene resin) | |||||
Note 1) When using a liquid fluid, the surge pressure must be under the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to the fittings and tubing. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tubing bursting.
Note 2) Do not use this product in a manner in which the tubing is not fixed. Observe the lesser value of the maximum operating pressure between the tubing and fittings. A material change over a long duration or due to high temperature may cause leakage. Perform periodic maintenance and replace with a new product immediately when abnormalities are detected.
Note 3) The minimum bending radius is the representative value measured as shown in the figure on the left.
- Use a tube above the recommended minimum bending radius.
- The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
- The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.
How to measure the minimum bending radius
Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.
Maximum operating pressure
Specifications of Soft Fluoropolymer Tubing TID Series
| Size | Inch Size | |||||
|---|---|---|---|---|---|---|
| Nominal | TID01 | TID05 | TID07 | TID11 | TID13 | |
| Outer diameter | inch | 1/8 " | 3/16 " | 1/4 " | 3/8 " | 1/2 " |
| mm | 3.18 | 4.75 | 6.35 | 9.53 | 12.7 | |
| Inner diameter | inch | 0.086 " | 0.124 " (1/8 ") | 0.156 " (5/32 ") | 0.25 " (1/4 ") | 0.374 " (3/8 ") |
| mm | 2.18 | 3.15 | 3.95 | 6.33 | 9.5 | |
| Roll | 8 m (25 ft) | ● | ● | ● | ● | ● |
| 16 m (50 ft) | ● | ● | ● | ● | ● | |
| Color | Translucent (material color) | |||||
| Applicable Fluids | See the catalog for applicable fluids. | |||||
| FluidNote 1) | Air, waterNote 1), inert gas | |||||
| Applicable fittingsNote 2) | Stainless steel 316 inert fittings KFG2 series Fluoropolymer Fittings LQ Series | |||||
| Maximum operating pressure (MPa) | 20°C | 1.4 | 1.4 | 1.6 | 1.4 | 0.9 |
| 100°C | 0.7 | 0.7 | 0.9 | 0.7 | 0.5 | |
| 200°C | 0.35 | 0.35 | 0.45 | 0.35 | 0.25 | |
| 260°C | 0.2 | 0.2 | 0.23 | 0.2 | 0.15 | |
| Minimum bending radius mmNote 3) | Recommended radius | 15 | 20 | 25 | 40 | 75 |
| Tube close bend radius | 9 | 10 | 15 | 23 | 42 | |
| Maximum operating temperature (fixed usage) | 260°C | |||||
| Material | Modified PTFE (Polytetrafluoroethylene resin) | |||||
Note 1) When using a liquid fluid, the surge pressure must be under the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to the fittings and tubing. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tubing bursting.
Note 2) Do not use this product in a manner in which the tubing is not fixed. Observe the lesser value of the maximum operating pressure between the tubing and fittings. A material change over a long duration or due to high temperature may cause leakage. Perform periodic maintenance and replace with a new product immediately when abnormalities are detected.
Note 3) The minimum bending radius is the representative value measured as shown in the figure on the left.
- Use a tube above the recommended minimum bending radius.
- The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
- The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.
How to measure the minimum bending radius
Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.
Maximum operating pressure
Codice componente
|
|---|
| TID01-8 |
| Codice componente |
Prezzo unitario standard
| Quantità minima d'ordine | Sconto volumi elevati | D.E. D (Ø) | D.E. [Distinzione] | D.I. d (Ø) | D.I. [Distinzione] | Min. raggio di curvatura (mm) | Bundle winding length (m) | Applicable Tube Size | Pressione d'esercizio massima (MPa) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
35.58 € | 1 | 4 giorni | 3.18 | Fino a 4 | - | Fino a 3 | 15 | 8 | Misura in pollici | 1.4 |
Loading...
Informazioni di base
| Tipo | Dritto | Uso servizio taglio | NA | Materiale | Fluororesina |
|---|---|---|---|---|---|
| Liquido applicabile | Acqua / Aria | Ambiente d'esercizio | Standard / Resistenza chimica | Colore | Trasparente |
| Temperatura d'esercizio(°C) | fino a 260 |
Si trova sulla pagina di Tubazione in fluoropolimero morbido serie TD/TID, il codice articolo è il seguente: TID01-8.
Ulteriori dettagli concernenti specifiche e dimensioni si trovano sotto il codice prodotto TID01-8.
Configura
Proprietà di base
-
D.I. d(Ø)
-
Tipo
- TD
- TID
-
D.E. D(Ø)
-
D.E. [Distinzione]
-
D.I. [Distinzione]
-
Bundle winding length(m)
-
Applicable Tube Size
- Misura in pollici
- Misura metrica
-
Pressione d'esercizio massima(MPa)
- 0.9
- 1.4
- 1.6
Filtrare per giorni di spedizione standard
-
- Tutti gli articoli
- 4 giorni o meno
- 22 giorni o meno
- 26 giorni o meno
- 66 giorni o meno
Attributi opzionali
- For specifications and details, please refer to the catalog.
- Specifiche e dimensioni di alcuni componenti potrebbero non essere illustrate in modo esauriente. Per i dettagli esatti, consultare i cataloghi dei produttori .
Tipologia prodotto
| Codice componente |
|---|
| TD0604-20 |
| TD0806-10 |
| TD0806-20 |
| TID05-16 |
| TID05-8 |
| TID07-16 |
| Codice componente | Prezzo unitario standard | Quantità minima d'ordine | Sconto volumi elevati | Giorni spedizione standard ? | D.E. D (Ø) | D.E. [Distinzione] | D.I. d (Ø) | D.I. [Distinzione] | Min. raggio di curvatura (mm) | Bundle winding length (m) | Applicable Tube Size | Pressione d'esercizio massima (MPa) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
254.89 € | 1 | 66 giorni | 6 | Fino a 6 | 4 | Fino a 4 | 25 | 20 | Misura metrica | 1.4 | ||
186.23 € | 1 | 22 giorni | 8 | Fino a 8 | 6 | Fino a 6 | 45 | 10 | Misura metrica | 0.9 | ||
372.39 € | 1 | 4 giorni | 8 | Fino a 8 | 6 | Fino a 6 | 45 | 20 | Misura metrica | 0.9 | ||
133.68 € | 1 | 26 giorni | - | Fino a 5 | - | Fino a 4 | 20 | 16 | Misura in pollici | 1.4 | ||
66.81 € | 1 | 4 giorni | - | Fino a 5 | - | Fino a 4 | 20 | 8 | Misura in pollici | 1.4 | ||
262.98 € | 1 | 4 giorni | 6.35 | Fino a 7 | - | Fino a 4 | 25 | 16 | Misura in pollici | 1.6 |
Supporto tecnico
Metodo di pagamento
Produzione on demand
Certificati
Copyright © MISUMI Corporation All Rights Reserved.