MY1H-Z, Cilindro senza stelo a giunto meccanico, Modello guida lineare senza unità di regolazione corsa (Codici componente - Download CAD)
[Features]
· Piping on site is adjustable depending on the state of the installation.
· Adjusting the cushion needle is easy.
(i)Nota
- Le immagini dei prodotti sono rappresentazioni. I dati CAD non sono supportati da alcuni numeri di modello.
Codice componente
Qui sono indicati i codici componente
correlati al prodotto ricercato
Mechanically Jointed Rodless Cylinder, Linear Guide Type, MY1H-Z Series Specifications
Model Indication Method
Model indication method, image
Compatible auto switches
| Type | Special function | Lead wire outlet | Indicator light | Wiring (output) | Load voltage | Auto switch part number | Lead wire length (m) | Pre-wired connector | Compatible load | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DC | AC | Vertical outlet | Lateral outlet | 0.5 (no mark) | 1 (M) | 3 (L) | 5 (Z) | None (N) | |||||||||
| Non-contact auto switch | - | Grommet | Available | 3-wire (NPN) | 24 V | 5 V, 12 V | - | M9NV | M9N | ● | ● | ● | ○ | ○ | ○ | IC circuit | Relay, PLC |
| 3-wire (PNP) | M9PV | M9P | ● | ● | ● | ○ | ○ | ○ | |||||||||
| 2-wire | 12 V | M9BV | M9B | ● | ● | ● | ○ | ○ | ○ | - | |||||||
| Diagnostic display (2-color display) | 3-wire (NPN) | 5 V, 12 V | M9NWV | M9NW | ● | ● | ● | ○ | ○ | ○ | IC circuit | ||||||
| 3-wire (PNP) | M9PWV | M9PW | ● | ● | ● | ○ | ○ | ○ | |||||||||
| 2-wire | 12 V | M9BWV | M9BW | ● | ● | ● | ○ | ○ | ○ | - | |||||||
| Part with enhanced water resistance (2-color display) | 3-wire (NPN) | 5 V, 12 V | Note 1M9NAV | Note 1M9NA | ○ | ○ | ● | ○ | - | ○ | IC circuit | ||||||
| 3-wire (PNP) | Note 1M9PAV | Note 1M9PA | ○ | ○ | ● | ○ | - | ○ | |||||||||
| 2-wire | 12 V | Note 1M9BAV | Note 1M9BA | ○ | ○ | ● | ○ | - | ○ | - | |||||||
| Contact auto switch | - | Grommet | Available | 3-wire (NPN equivalent) | - | 5 V | - | A96V | A96 | ● | - | ● | - | - | - | IC circuit | - |
| 2-wire | 24 V | 12 V | 100 V | Note 2A93V | A93 | ● | ● | ● | ● | - | - | - | Relay, PLC | ||||
| NA | 100 V or less | A90V | A90 | ● | - | ● | - | - | - | IC circuit | |||||||
- Note 1 Auto switches with enhanced water resistance can be mounted on the above model products, but that does not guarantee the water-resistant performance of the product.
Confirm with the manufacturer for regarding the above models with enhanced water resistance. - Note 2 The type with a 1 m lead wire only supports D-A93.
Specifications chart
| Tube inner diameter (mm) | 25 | 32 | 40 | |
|---|---|---|---|---|
| Usable fluids | Air | |||
| Operating type | Double-acting type | |||
| Operating pressure range | 0.1 to 0.8 MPa | |||
| Guaranteed pressure resistance | 1.2 MPa | |||
| Ambient temperature and working fluid temperature | 5 to 60°C | |||
| Cushion | Air cushion | |||
| Lubrication | Lubrication-free | |||
| Allowable difference of stroke length | 0 to +1.8 | |||
| Piping connection port diameter | Front/side port | Rc 1/8 | Rc 1/4 | |
| Bottom port | ø6 (diameter 6 mm) | ø8 (diameter 8 mm) | ||
Made-to-order specifications
| Display symbol | Specifications/details |
|---|---|
| -X168 | Helical coil insert screw specifications |
Made-to-order specifications
| Display symbol | Specifications/details |
|---|---|
| -XB10 | Intermediate stroke (dedicated body used) |
| -XB11 | Long stroke type |
| -XB22 | Shock absorber / soft type RJ series-equipped |
| -XC56 | Includes dowel pins |
Lock specifications
| Tube inner diameter (mm) | 25 | 32 | 40 |
|---|---|---|---|
| Lock position | One side (selectable), both sides | ||
| Retention (MAX.) N | 270 | 450 | 700 |
| Stroke adjustable range (mm) | 0 to -11.5 | 0 to -12 | 0 to -16 |
| Backlash | 1 mm or less | ||
| Manual unlock | Allowable (non-locking type) | ||
Operating piston speed
| Tube inner diameter (mm) | 25 to 40 | |
|---|---|---|
| No stroke adjustment unit | 100 to 1,000 mm/s | |
| Stroke adjustment unit | A unit | 100 to 1,000 mm/sNote 1) |
| L unit, H unit | 100 to 1,500 mm/sNote 2) | |
Note 1: Air cushioning performance is reduced when the adjusting bolt is used to increase the stroke adjustment. Meanwhile, in ranges exceeding the air cushion stroke, the working piston speed will become 100 to 200 mm/s.
Note 2: The working piston speed will become 100 to 1,000 mm/s when using centralized piping.
Note 3: Use at a speed within the range of the absorption capacity.
Stroke adjustment unit specifications
| Tube inner diameter (mm) | 25 | 32 | 40 | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Unit symbol | A | L | H | A | L | H | A | L | H | |
| Configuration details Shock absorber model | Adjusting bolt included | RB 1007 + Adjusting bolt included | RB 1412 + Adjusting bolt included | Adjusting bolt included | RB 1412 + Adjusting bolt included | RB 2015 + Adjusting bolt included | Adjusting bolt included | RB 1412 + Adjusting bolt included | RB 2015 + Adjusting bolt included | |
| Stroke adjustment range of each spacer for intermediate fixing (mm) | No spacer | 0 to -11.5 | 0 to -12 | 0 to -16 | ||||||
| With short spacer | -11.5 to -23 | -12 to -24 | -16 to -32 | |||||||
| With long spacer | -23 to -34.5 | -24 to -36 | -32 to -48 | |||||||
- *The stroke adjustment range is the adjustment range of one side when attached to a cylinder.
Stroke adjustment unit symbol
| - | Right stroke adjustment unit | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| No unit | A: Adjusting bolt included | L: Shock absorber for low loads and adjusting bolt included | H: Shock absorber for high loads and adjusting bolt included | |||||||||
| - | With short spacer | With long spacer | - | With short spacer | With long spacer | - | With short spacer | With long spacer | ||||
| Left side stroke adjustment unit | No unit | No mark | SA | SA6 | SA7 | SL | SL6 | SL7 | SH | SH6 | SH7 | |
| A: Adjusting bolt included | - | AS | A | AA6 | AA7 | AL | AL6 | AL7 | AH | AH6 | AH7 | |
| With short spacer | A6S | A6A | A6 | A6A7 | A6L | A6L6 | A6L7 | A6H | A6H6 | A6H7 | ||
| With long spacer | A7S | A7A | A7A6 | A7 | A7L | A7L6 | A7L7 | A7H | A7H6 | A7H7 | ||
| L: Shock absorber for low loads and adjusting bolt included | - | LS | LA | LA6 | LA7 | L | LL6 | LL7 | LH | LH6 | LH7 | |
| With short spacer | L6S | L6A | L6A6 | L6A7 | L6L | L6 | L6L7 | L6H | L6H6 | L6H7 | ||
| With long spacer | L7S | L7A | L7A6 | L7A7 | L7L | L7L6 | L7 | L7H | L7H6 | L7H7 | ||
| H: Shock absorber for high loads and adjusting bolt included | - | HS | HA | HA6 | HA7 | HL | HL6 | HL7 | H | HH6 | HH7 | |
| With short spacer | H6S | H6A | H6A6 | H6A7 | H6L | H6L6 | H6L7 | H6H | H6 | H6H7 | ||
| With long spacer | H7S | H7A | H7A6 | H7A7 | H7L | H7L6 | H7L7 | H7H | H7H6 | H7 | ||
- *The spacer for intermediate fixing of the stroke adjustment unit cannot be used on the side to when the end lock is attached.
- *The spacer is a mounting bracket for fixing the stroke adjustment unit in an intermediate position of the stroke.
The model number of the shock absorber for the L and H units
| Type | Stroke adjustment unit | Tube inner diameter (mm) | ||
|---|---|---|---|---|
| 25 | 32 | 40 | ||
| Standard (shock absorber RB series) | L | RB1007 | RB1412 | |
| H | RB1412 | RB2015 | ||
| Shock absorber / soft type RJ series-equipped (-XB22) | L | RJ1007H | RJ1412H | |
| H | RJ1412H | - | - | |
- *The lifespan of the shock absorber is different from that of the MY1H cylinder main body.
- *The shock absorber / soft type RJ series-equipped (-XB22) has made-to-order specifications.
Shock absorber specifications
| Model | RB 1007 | RB 1412 | RB 2015 | |
|---|---|---|---|---|
| Maximum energy absorption (J) | 5.9 | 19.6 | 58.8 | |
| Stroke absorption (mm) | 7 | 12 | 15 | |
| Maximum collision velocity (mm/s) | 1,500 | 1,500 | 1,500 | |
| Maximum operating frequency (cycle/min) | 70 | 45 | 25 | |
| Spring force (N) | When expanded | 4.22 | 6.86 | 8.34 |
| When compressed | 6.86 | 15.98 | 20.50 | |
| Operating temperature range (°C) | 5 to 60 | |||
- *The lifespan of the shock absorber will differ from that of the MY1H cylinder main body depending on the use conditions.
Standard type, structural drawing
Standard type, structural drawing
Components
| Number | Description | Materials | Additional notes |
|---|---|---|---|
| 1 | Cylinder tube | Aluminum alloy | Hard anodized aluminum |
| 2 | Head cover | Aluminum alloy | Painted |
| 3 | Cushion boss | Special resin | - |
| 4 | Slide table | Aluminum alloy | Hard anodized aluminum |
| 5 | Piston yoke | Aluminum alloy | Chromate |
| 6 | Piston | Aluminum alloy | Chromate |
| 7 | Wear ring | Special resin | - |
| 8 | Belt separator | Special resin | - |
| 9 | Guide roller | Special resin | - |
| 10 | Parallel pin | Stainless steel | - |
| 11 | Coupler | Ferrous sintered material | - |
| 12 | Head plate | Stainless steel | - |
| 13 | Cushion needle | Rolled steel | Nickel plating |
| 14 | Belt clamp | Special resin | - |
| 17 | Guide | - | - |
| 18 | End cover | Special resin | - |
| 20 | Steel ball | Carbon tool steel | - |
| 21 | Bearing | Special resin | - |
| 22 | Magnet | Rare earth magnet | - |
| 23 | Square nut | Carbon steel | Chromate |
| 24 | Spring pin | Bearing steel | - |
| 26 | Thin-head screw | Chrome molybdenum steel | Chromate |
| 27 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 28 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 29 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 33 | Hex socket head taper plug (tapered) | Carbon steel | Chromate (in the case of centralized piping: 10 pcs.) |
| 34 | Hex socket head taper plug (tapered) | Carbon steel | Chromate (in the case of centralized piping: 4 pcs.) |
| 38 | Stopper | Carbon steel | - |
| 39 | Spacer | Stainless steel | - |
| 40 | Hex socket head cap button screw | Chrome molybdenum steel | Chromate |
| 41 | CR-type retaining ring | Steel for springs | - |
| 42 | Seal magnet | Rubber magnet | - |
| 43 | Lub-retainer | Special resin | - |
Replacement parts / seal kit
| Number | Description | Materials | Quantity | MY1H25 | MY1H32 | MY1H40 |
|---|---|---|---|---|---|---|
| 15 | Seal belt | Urethane | 1 | MY25-16C-[stroke] | MY32-16C-[stroke] | MY40-16C-[stroke] |
| 16 | Dust seal band | Stainless steel | 1 | MY1B25-16B-[stroke] | MY1B32-16B-[stroke] | MY1B40-16B-[stroke] |
| 25 | Cushion boss gasket | NBR | 2 | MYB25-16GA5900 | MYB32-16GA5901 | MYB40-16GA5902 |
| 36 | O-ring | NBR | 2 | KA00311 | KA00320 | KA00320 |
| (ø5.1 (diameter 5.1 mm) ×; ø3 (diameter 3 mm ×; ø1.05 (diameter 1.05 mm)) | (ø7.15 (diameter 7.15 mm) ×; ø3.75 (diameter 3.75 mm) ×; ø1.7 (diameter 1.7 mm)) | (ø7.15 (diameter 7.15 mm) ×; ø3.75 (diameter 3.75 mm) ×; ø1.7 (diameter 1.7 mm)) | ||||
| 37 | Side scraper | Special resin | 2 | MYH25-15BK2902B | MYH32-15BK2903B | MYH40-15BK2904B |
| 19 | Scraper | NBR | 2 | MY1H25-PS | MY1H32-PS | MY1H40-PS |
| 30 | Piston packing | NBR | 2 | |||
| 31 | Cushion seal | NBR | 2 | |||
| 32 | Tube gasket | NBR | 2 | |||
| 35 | O-ring | NBR | 2 |
- *Because the seal kit includes 19, 30, 31, 32, and 35, order using the order number of each tube inner diameter.
- *The seal kit includes a grease pack (10 g).
A grease pack (20 g) is included when 15 or 16 are shipped as single items.
End lock structural drawing
End lock structural drawing
Components
| Number | Description | Materials | Additional notes |
|---|---|---|---|
| 1 | Body for locking | Aluminum alloy | Painted |
| 2 | Lock finger | Carbon steel | Nickel plating after quenching |
| 3 | Lock finger fixture | Rolled steel | Nickel plating |
| 4 | Lock piston | Carbon tool steel material | Kanizen plating after quenching |
| 5 | Rod cover | Aluminum alloy | Hard anodized aluminum |
| 6 | Return spring | Spring steel | Zinc chromate |
| 7 | Bypass pipe | Aluminum alloy | Hard anodized aluminum |
| 10 | Steel ball | High-carbon chromium bearing steel | - |
| 11 | Steel ball | High-carbon chromium bearing steel | - |
| 13 | Round R-shaped retaining ring | Carbon tool steel | Nickel plating |
| 15 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 16 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 17 | Steel ball | High-carbon chromium bearing steel | - |
| 18 | Steel ball | High-carbon chromium bearing steel | - |
| 19 | Head cover WR | Aluminum alloy | Painted |
| 20 | Head cover WL | Aluminum alloy | Painted |
| 21 | Cushion ring | Aluminum alloy | - |
| 22 | Hex socket set screw | Chrome molybdenum steel | Chromate |
Replacement parts / seal kit
| Number | Part name | Materials | Quantity | MY1H25 | MY1H32 | MY1H40 |
|---|---|---|---|---|---|---|
| 8 | Rod packing | NBR | 1 | KB00267 | KB00267 | KB00267 |
| 9 | Piston packing | NBR | 1 | KB00217 | KB00217 | KB00217 |
| 12 | O-ring | NBR | 1 | KB00037 | KB00037 | KB00037 |
| 14 | O-ring | NBR | 2 | KA00048 | KA00048 | KA00048 |
- *The packing does not include a grease pack; please make arrangements separately.
Codice componente
|
|---|
| MY1H25-1500HZ |
| MY1H40-1500Z |
| Codice componente | Relativo a |
Prezzo unitario standard
| Quantità minima d'ordine | Sconto volumi elevati | Tipo | Corsa (mm) | Materiale tavola | Max. Massa di carico (gamma selezionabile) (kg) | Max. Massa di carico (kg) | Lunghezza tavola L (mm) | D.I. cilindro (Ø) | Giunto cilindro senza barra | Ambiente d'esercizio | Trattamento superficie tavola | Guida | Larghezza tavola W (mm) | Altezza tavola H (mm) | Pressione di esercizio (MPa) | Piping Format | Port Screw Type | Cushion | Auto Switch | Lead Wire Length (m) | Number of Switches | Custom-made Specifications | End Block | Model | Stroke Adjustment Unit Symbol | Custom-made | Spacer for intermediate fixing | Spacer shipping form | Type | Applicable inner diameter of cylinder (ø) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | 2,465.37 € | 1 | 9 giorni | “Cilindro senza asta” | 1,500 | [Alluminio] Lega di alluminio | 20 to 39.9 | 27.5 | 114 | 25 | Con giunto meccanico | Uso generico | [Anodizzato trasparente] Alluminio anodizzato duro | [Guida di scorrimento] Con guida lineare | 90 | 54 | 0,1 – 0,8 | Tipo standard | Rc | Cuscino d'aria | - | Magnete incorporato | Assente | - | Assente | - | - | Assente | - | - | Cilindro | - | ||
3,144.89 € | 1 | 9 giorni | “Cilindro senza asta” | 1,500 | [Alluminio] Lega di alluminio | 40 to 57 | 50 | 170 | 40 | Con giunto meccanico | Uso generico | [Anodizzato trasparente] Alluminio anodizzato duro | [Guida di scorrimento] Con guida lineare | 121 | 84 | 0,1 – 0,8 | Tipo standard | Rc | Cuscino d'aria | - | Magnete incorporato | Assente | - | Assente | - | - | Assente | - | - | Cilindro | - |
Loading...
Configura
Proprietà di base
-
Tipo
- “Cilindro senza asta”
- Altro
-
Materiale tavola
- Alluminio
- Alluminio
-
Max. Massa di carico (gamma selezionabile)(kg)
-
Max. Massa di carico(kg)
-
Lunghezza tavola L(mm)
-
D.I. cilindro(Ø)
-
Giunto cilindro senza barra
- Con giunto meccanico
-
Ambiente d'esercizio
- Uso generico
-
Trattamento superficie tavola
- Anodizzato trasparente
- Anodizzato trasparente
-
Guida
- Guida di scorrimento
- Guida di scorrimento
-
Larghezza tavola W(mm)
-
Altezza tavola H(mm)
-
Pressione di esercizio(MPa)
-
Piping Format
-
Port Screw Type
- G
- NPT
- Rc
-
Cushion
-
Auto Switch
- M9B
- M9BW
- M9BWV
- M9P
- M9PW
- A93
- Assente
- Nessuno
-
Lead Wire Length(m)
-
Number of Switches
-
Custom-made Specifications
- 0.5
- 3
-
End Block
- Assente
-
Model
-
Stroke Adjustment Unit Symbol
- 0.1–0.8
- H6
- H6H
- HH6
- L6
- L6L
- SL6
- A6L6
- L6A6
- A6H7
- H6H7
- H7
- HH7
- HL7
- L7
- LL7
- SL7
- L7L6
- A
- AH
- AL
- H
- HS
- L
- LH
- LS
- No unit
- SL
- Senza corsa
-
Custom-made
- Assente
- Con fori per tasselli
- Specifica della filettatura dell’inserto della bobina elicoidale
-
Spacer for intermediate fixing
- Distanziatore corto
- Distanziatore lungo
- Nessun distanziatore
-
Spacer shipping form
- Solo distanziatore
- Unità incorporata
-
Type
- Cilindro
- Unità regolazione corsa
-
Applicable inner diameter of cylinder(ø)
-
Tipo
- MY1H-Z
- MYH-A
-
Corsa(mm)
-
Filtrare per tipo dati CAD
- 2D
- 3D
Filtrare per giorni di spedizione standard
-
- Tutti gli articoli
- 4 giorni o meno
- 7 giorni o meno
- 8 giorni o meno
- 9 giorni o meno
- 14 giorni o meno
- 16 giorni o meno
- 17 giorni o meno
- 22 giorni o meno
- 26 giorni o meno
- 98 giorni o meno
Attributi opzionali
- Product pictures are representations. CAD data is not supported by some of the model numbers.
- Specifiche e dimensioni di alcuni componenti potrebbero non essere illustrate in modo esauriente. Per i dettagli esatti, consultare i cataloghi dei produttori .
Supporto tecnico
Metodo di pagamento
Produzione on demand
Certificati
Copyright © MISUMI Corporation All Rights Reserved.