MITUTOYO Campioni di durezza

?* Informazioni su tempi di consegna e prezzi

• 

  Shore Hardness Reference Material

  MITUTOYO

  Shore test specimen sets (3pcs.) Please note:
  Recommended storage temperature: 23 °C ±5 °CHumidity 50 % ±15 %.For best results, climate to laboratory conditions for min.
  12 hours: 23 °C ±1 °C. Humidity 50 % ±10 %. Incorrect room temperature and humidity causes other readings.
  Annual recalibration of test specimen is recomended.
  Shore test specimen should not be older than 2 years from initial calibration.
  Please replace after 2 years.Please contact us if you do not find what you are looking for.

  A partire da∗ ：	335.13 €
  Consegna da ：	5 giorni

  *Prezzo unitario in configurazione base

• 

  Campione di durezza Rockwell

  MITUTOYO

  Hardness reference materials in quality control:
  The boost for your process safety! The daily verification, performed by the user, is described in the according hardness testing standards and significantly contributes to quality management processes.
  In the daily verification process, all parameters of the hardness test system that build up to the hardness value, are examined by indentations on the hardness reference material.
  This periodical inspection of the machine by means of hardness reference materials should be carried out immediately before the daily start of the test schedule.
  An according documentation enhances the process safety, as value shifts due to damage or malfunction can be detected easily.
  In addition, the repeatability of results of the hardness testing machine can also be checked with the hardness reference materials.
  Mitutoyo offers a comprehensive range of hardness reference materials (hardness test blocks) in different materials with hardness levels to suit your quality management procedure perfectly.
  Mitutoyo reference materials:
  High-end quality Made in Germany - Independent DAkkS calibration according to DIN EN ISO 6508 and/or ASTM E18 in an accredited laboratory Large square or rectangular surface with large space advantage over triangular or round test blocks Short delivery time MPE "Maximum Permissible Error" of the hardness testing system engraved (does apply for carbide materials) – all relevant information at a glance.
  A range of additional services can be ordered:
  - Up to three different scales on one reference material (Does not apply for Brinell materials)
  - A lasered grid on the surface for accurate indentation spacing
  - Alternative ASTM accredited calibration
  - Double calibration according to ISO and ASTM standards
  - Compare the surface sizes for the evaluation of the price - performance ratio.

  A partire da∗ ：	398.68 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Campione di durezza Leeb

  MITUTOYO

  Hardness reference materials in quality control:
  The boost for your process safety! The daily verification, performed by the user, is described in the according hardness testing standards and significantly contributes to quality management processes. In the daily verification process, all parameters of the hardness test system that build up to the hardness value, are examined by indentations on the hardness reference material.
  This periodical inspection of the machine by means of hardness reference materials should be carried out immediately before the daily start of the test schedule.
  An according documentation enhances the process safety, as value shifts due to damage or malfunction can be detected easily.
  In addition, the repeatability of results of the hardness testing machine can also be checked with the hardness reference materials.
  Mitutoyo offers a comprehensive range of hardness reference materials (hardness test blocks) to suit your quality management procedure perfectly.

  A partire da∗ ：	313.75 €
  Consegna da ：	5 giorni

  *Prezzo unitario in configurazione base

• 

  Penetratore in diamante Vickers

  MITUTOYO

  Mitutoyo indenters for Vickers hardness test
  As the interface between machine and material, the indenter must be of immaculate quality.
  Therefore Mitutoyo only uses diamond indenters from the most experienced suppliers.
  The indenters are calibrated in the highest standard calibration laboratories in the DAkkS accreditation body, accredited according to ISO 17025 and traceable to the PTB.
  Constant development at our calibration partners secures an unmatched quality level.
  Vickers diamond indenter feature DAkkS calibration certificates according to DIN EN ISO 6507-2 and/or ASTM E92.
  The line of conjunction between opposite faces of the diamond pyramid are measured with the latest technologies.
  The line appears due to the grinding process.
  From that parameter, the usability of the indenter is determined by categorising them by the length of the line.
  Mitutoyo offers Vickers pyramid indenters usable from HV0.001 (junction line 0.5µm), HV0.2 (junction line 1.0µm) and HV5 (junction line 2.0µm), at different price levels.
  The values include uncertainty of measurement. Therefore it is impossible to judge the line of a Micro Vickers indenter with a conventional light microscope.

  A partire da∗ ：	438.16 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Campione di durezza Brinell

  MITUTOYO

  Hardness reference materials in quality control:
  The boost for your process safety! The daily verification, performed by the user, is described in the according hardness testing standards and significantly contributes to quality management processes.
  In the daily verification process, all parameters of the hardness test system that build up to the hardness value, are examined by indentations on the hardness reference material.
  This periodical inspection of the machine by means of hardness reference materials should be carried out immediately before the daily start of the test schedule.
  An according documentation enhances the process safety, as value shifts due to damage or malfunction can be detected easily. In addition, the repeatability of results of the hardness testing machine can also be checked with the hardness reference materials.
  Mitutoyo offers a comprehensive range of hardness reference materials (hardness test blocks) in different materials with hardness levels ranging from 80 to 650HBW to suit your quality management procedure perfectly.
  The tolerance for the nominal value of the hardness testblock is ± 25HBW.
  Mitutoyo reference materials:
  High-end quality Made in Germany - Independent DAkkS calibration according to DIN EN ISO 6506 and/or ASTM E10 in an accredited laboratory Large square or rectangular surface with large space advantage over triangular or round test blocks Short delivery time MPE "Maximum Permissible Error" of the hardness testing system engraved (does apply for carbide materials) – all relevant information at a glance.
  A range of additional services can be ordered:
  - Up to three different scales on one reference material (Does not apply for Brinell materials)
  - A lasered grid on the surface for accurate indentation spacing
  - Alternative ASTM accredited calibration.
  - Double calibration according to ISO and ASTM standards
  - A tighter tolerance of ± 15HBW for the nominal value
  - Compare the surface sizes for the evaluation of the price - performance ratio.

  A partire da∗ ：	453.95 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Campione di durezza Vickers

  MITUTOYO

  Hardness reference materials in quality control:
  The boost for your process safety! The daily verification, performed by the user, is described in the according hardness testing standards and significantly contributes to quality management processes. In the daily verification process, all parameters of the hardness test system that build up to the hardness value, are examined by indentations on the hardness reference material.
  This periodical inspection of the machine by means of hardness reference materials should be carried out immediately before the daily start of the test schedule.
  An according documentation enhances the process safety, as value shifts due to damage or malfunction can be detected easily. In addition, the repeatability of results of the hardness testing machine can also be checked with the hardness reference materials.
  Mitutoyo offers a comprehensive range of hardness reference materials (hardness test blocks) in different materials with hardness levels ranging from 80HV to 2100HV to suit your quality management procedure perfectly.
  The tolerance for the nominal value of steel and aluminium hardness testblocks is ± 25HV. (Does not apply for carbide materials) For carbide reference materials, the actual calibrated value can be significantly higher.
  Mitutoyo reference materials:
  High-end quality Made in Germany - Independent DAkkS calibration according to DIN EN ISO 6507 and/or ASTM E92 in an accredited laboratory Large square or rectangular surface with large space advantage over triangular or round test blocks Short delivery time MPE “Maximum Permissible Error” of the hardness testing system engraved (does apply for carbide materials) – all relevant information at a glance.
  If the diagonal lengths are outside the 20µm limit of ISO 6507 the reference material is exclusively supplied with ASTM E92 calibration certificates.
  A range of additional services can be ordered:
  - Up to three different scales on one reference material (Does not apply for Brinell materials)
  - A lasered grid on the surface for accurate indentation spacing
  - Alternative ASTM accredited calibration.
  - Double calibration according to ISO and ASTM standards
  - A tighter tolerance of ± 15HV for the nominal value (Does not apply for carbide materials)
  - Compare the surface sizes for the evaluation of the price - performance ratio.

  A partire da∗ ：	560.53 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Knoop Hardness Reference Material

  MITUTOYO

  Hardness reference materials in quality control:
  The boost for your process safety! The daily verification, performed by the user, is described in the according hardness testing standards and significantly contributes to quality management processes.
  In the daily verification process, all parameters of the hardness test system that build up to the hardness value, are examined by indentations on the hardness reference material.
  This periodical inspection of the machine by means of hardness reference materials should be carried out immediately before the daily start of the test schedule.
  An according documentation enhances the process safety, as value shifts due to damage or malfunction can be detected easily. In addition, the repeatability of results of the hardness testing machine can also be checked with the hardness reference materials.
  Mitutoyo offers a comprehensive range of hardness reference materials (hardness test blocks) in different materials with hardness levels ranging from 200 to 2100HK to suit your quality management procedure perfectly.
  The tolerance for the nominal value of steel and aluminium hardness testblocks is ± 25HK. (Does not apply for carbide materials) For carbide reference materials, the actual calibrated value can be significantly higher.
  Mitutoyo reference materials:
  High-end quality Made in Germany - Independent DAkkS calibration according to DIN EN ISO 4545 and/or ASTM E92 in an accredited laboratory Large square or rectangular surface with large space advantage over triangular or round test blocks Short delivery time MPE "Maximum Permissible Error" of the hardness testing system engraved (does apply for carbide materials) – all relevant information at a glance.
  If the diagonal lengths are outside the 20µm limit of ISO 4545 the reference material is exclusively supplied with ASTM E92 calibration certificates.
  A range of additional services can be ordered:
  - Up to three different scales on one reference material (Does not apply for Brinell materials)
  - A lasered grid on the surface for accurate indentation spacing
  - Alternative ASTM accredited calibration.
  - Double calibration according to ISO and ASTM standards
  - A tighter tolerance of ± 15HK for the nominal value (Does not apply for carbide materials)
  - Compare the surface sizes for the evaluation of the price - performance ratio.

  A partire da∗ ：	560.53 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Penetratore in diamante Knoop

  MITUTOYO

  Mitutoyo indenters for Knoop hardness test
  As the interface between machine and material, the indenter must be of immaculate quality.
  Therefore Mitutoyo only uses diamond indenters from the most experienced suppliers.
  The indenters are calibrated in the highest standard calibration laboratories in the DAkkS accreditation body, accredited according to ISO 17025 and traceable to the PTB.
  Constant development at our calibration partners secures an unmatched quality level.
  Knoop diamond indenter feature DAkkS calibration certificates according to DIN EN ISO 4545-2 and/or ASTM E92.
  The line of conjunction between opposite faces of the diamond pyramid are measured with the latest technologies.
  The line appears due to the grinding process. The maximum length of the conjunction line is 1.0µm.

  A partire da∗ ：	1,009.21 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Penetratore in diamante Rockwell, tipo standard

  MITUTOYO

  Mitutoyo indenters for Rockwell hardness test
  As the interface between machine and material, the indenter must be of immaculate quality.
  Therefore Mitutoyo only uses diamond indenters from the most experienced suppliers.
  The indenters are calibrated in the highest standard calibration laboratories in the DAkkS accreditation body, accredited according to ISO 17025 and traceable to the PTB.
  Constant development at our calibration partners secures an unmatched quality level.
  Rockwell diamond indenter feature DAkkS calibration certificates according to DIN EN ISO 6508-2 and/or ASTM E18.
  A function test, verifying the applicability of the indenter in regard of various indentation depth levels under different test forces, is optionally available.
  Ball holders are made by Mitutoyo, and are supplied without calibration certificate for the included ball.

  A partire da∗ ：	453.95 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

• 

  Diamond cone indenter for Rockwell test, slim type

  MITUTOYO

  Mitutoyo indenters for Rockwell hardness test
  As the interface between machine and material, the indenter must be of immaculate quality.
  Therefore Mitutoyo only uses diamond indenters from the most experienced suppliers.
  The indenters are calibrated in the highest standard calibration laboratories in the DAkkS accreditation body, accredited according to ISO 17025 and traceable to the PTB.
  Constant development at our calibration partners secures an unmatched quality level.
  Rockwell diamond indenter feature DAkkS calibration certificates according to DIN EN ISO 6508-2 and/or ASTM E18.
  A function test, verifying the applicability of the indenter in regard of various indentation depth levels under different test forces, is optionally available.
  Ball holders are made by Mitutoyo, and are supplied without calibration certificate for the included ball.

  A partire da∗ ：	400.00 €
  Consegna da ：	60 giorni

  *Prezzo unitario in configurazione base

Loading...